You can muffle the beeper pretty effectively with some tape, the old air fryer we had terrified one of the dogs because of the incessant beeping. My coffee scale by default beeps whenever you touch it, thankfully that’s 100% mutable.

I also hate this.

I’ve been playing rogue trader on mine recently, I’d describe as playable, but it’s night and day different going through moonlight (which yeah, obviously). Satisfactory was able to get 40-60 pretty reliably.

How bad is bg3 on it?

We don’t even need to look stateside, attacking the judiciary is nothing new for the Tories.

Comment with my exact question, is this variance beyond MoE? Would love to see their methodology on how this is calculated.

Yeah, makes sense based on where the sensor is, my heater didn’t have a thermocouple on it so I drilled a hole for a thermistor midplate, it’s super slow to respond is the downside but in theory it should be accurate enough.

I don’t have experience with the bambu, in theory everything will experience thermal expansion but for the voron setup, the bimetallic construction is some of the issue, they have different thermal expansion properties so it can cause deflections. Part quality will vary wildly depending on sourcing too, vorons are very diy and open as the draw, but there’s just so much variability from sourcing, mods, assembly etc.

I have z braces on my bear modded mk3s too, things reliable as heck and easy to service.

It looked like you have a textured sheet? 0.2 mm variation over the entire built area isn’t huge, might be exaggerating it.

How much of a heat soak? If you’re going to the edge, let that sit for at least an hour, preferably more, look at Ellis’ page on thermal expansion, frame will absolutely expand. I use backers on my 2.4, gantry is giant bimetallic strip, backers do seem to help with that. Klipper does have the ability to correct for this as well, in that link. I do also have a kinematic bed mount (it’s coupled loosely to the frame, basically gives the bed room to expand), which again does seem to help, but I’d personally say heat soak is the first thing to do to achieve consistency.

And to echo others, degrease your bed with dish soap & water (unless your surface can be damaged, Buildtak that’s a no, don’t of that for example). If that’s a textured sheet, may need to give a bit more of a squish, but get it good and clean first. Ellis has some solid 1st layer calibration and troubleshooting guides to go through. For pei, personally I’ve found I needed to rough up the surface a bit with a brass brush, I don’t love pei on my voron, usually use buildtak but have had really good results with the fire resistant version of garolite.

Edit: read up on your probe, eddy current based? Sounds really interesting, my first point is probably moot, though possible you could be picking up the texture or if you have strong magnets it could affect it (my bed has an array of strong round magnets, seen others that are just a magnetic sheet), the do call that out in their FAQ.

One part of me hopes the Reform and PCs split again after this, but realistically idk that’s happening. Leslyn Lewis will totally run again, if they’re doubling down on those ideas might be they select her.

I was looking through, generally custom macros are in the config folder, unsure if they’ve implemented it differently, here’s the Raise3D repo I found earlier, klipper has some code in c for the microcontroller stuff AFAIK with klippy in python, I’ve not personally dove into the code, just config and macro stuff largely.

Actually digging through a bit, there’s some gcodes in /klippy/gcode.py in the above repo I don’t see in the Mainline Klipper equivalent, like M9999, it might be a start, klippy lives on the host machine.

From reddit, some stuff, I kinda got the same vibes you did a while back, got a shit disturber vibe, does things to intentionally piss people off, which was what I got from that open carry video in that reddit comment.

Yeah, didn’t think it was an image, just images in gcode are encoded.

I did find their github with a klipper config, but yeah, unsurprisingly it’s not there. You could see if it has documentation through the klipper console? I’m betting it’s not going to be in your klipper config unfortunately. Definitely leaning toward it being the portion that has the firmware validate the key and then set things up.

From the arch wiki

sudo -e {file}

Set SUDO_EDITOR in your profile to the editor of your choice, benefit is it retains your user profile for that editor, it’s also less to type. For stuff like editing sudoers you’re supposed to use visudo to edit that. Others can probably give better/more thorough reasons to consider it.

Prefacing this, I have no idea, can’t find any information either, I’m just speculating for what it’s worth.
.What’s kinda interesting is someone posted an identical one to the prusa forums like 2 years ago, no responses unfortunately.

I’m willing to guess it’s data, I’d wondered if it was unique per user but if you both have encountered it… don’t think that’s the case. I’m going to assume it’s sending a blob, vaguely reminds me of image thumbnails in gcode, but those are clear that’s what they are, maybe it’s some executable code that changes printer parameters or how the subsequent gcode is processed by the controller to support the HyperFFF mode.

Don’t love it personally, but I’m willing to assume they’re doing this way to obfuscate what’s happening because its proprietary rather than anything malicious. I don’t really have the tools or knowledge to really try to examine it further however, hopefully someone with that skillset is interested enough.

Edit: is this a cloud first printer? Also totally possible it’s just telling the printer to download something remotely to support that HyperFFF mode, again, can’t really tell, could be worth seeing what’s happening network wise.

Canada’s National Observer asked the NDP for comment on the situation and later that day posed the question to NDP Leader Jagmeet Singh in a virtual press conference on April 22.

Singh did not directly respond to Canada’s National Observer’s question, nor its follow-up question about the Green Party’s complaint.

Instead he said many strategic voting websites regularly promote the Liberal Party and that “if you want to stop Conservatives, vote New Democrat. If you also want someone that’s going to … stop liberals like Mark Carney from cutting the things that you need, vote New Democrat.”

An hour later, an NDP spokesperson contacted Canada’s National Observer but did not offer a statement. Instead, they sent information “on background” — indicating it shouldn’t be attributed to the NDP — that pointed out the federal Green Party was sanctioned by Elections Canada in 2016, and said “that website isn’t ours.”

Gotta say I’m unhappy that I’m disappointed in the Federal NDP again, the whataboutism around the green party being sanctioned almost a decade ago is maybe tangentially relevant, but that feels they’re more trying to cast doubt on the green’s poll. Your candidate linked to the website, it doesn’t matter if it’s yours, its part of your party’s official communication. I don’t love that Singh (or any politician for that matter but I align closest historically with the NDP so I’ll be critical) seemingly didn’t address the questions during the press conference either.

There’s something about the current NDP priorities I don’t love, while I totally acknowledge their work on pharmacare, ban on scab labour and dental (and understand why they tore up the supply & confidence agreement over back to work), I started being disappointed back when they held back 100% of campaign rebates, I’ve personally noticed less and less riding level activity from then as well. I don’t love that they’re supporting S-210, I know a bunch of people who started listening to the NDP specifically because they were pretty adamant in their support for privacy. It’s a lot of small things but yeah, they add up.

I’m just happy to still be considered young lol.

My circle, most want the Feds to do more with what they can, but largely place blame on provinces & municipalities for housing & rent, Ontario removed rent controls for units built after 2018 when the pcpo formed government as one example. The lower levels of government have a larger impact on your day to day and yet have the lowest engagement, my (ndp) MPP even sent out a “this level of government is responsible for this” magnet with numbers and departments of it to (I think) help address that.

Yeah that’s my understanding too.

I used to get ones from the Tories a few years back, looks only (ignoring content) this is somehow tamer, those looked like Peter Popov mailers complete with the random fake pencil scrawls in the margins, highlighting and blue ink underlining.

As far as I recall, egg freezes, it dead. Always checked my hauling zones after I accidentally killed some dinosaur eggs (pretty sure it’s the same behaviour in vanilla)

Should reinstall anyhow, actually really liked anomaly!

That’s pretty much how I’d expect it to go yeah, every electrician I’ve worked with has been super particular about wiring. Even having done my own in-field bodges on wire looms for equipment (just splicing a wire because I didn’t have an available spare or time to redo the harness) it doesn’t stick out, especially after all the cable wrap or zip ties.

Trying to be vague as heck in the spoilers, totally get it! Don’t think there’s anything there that’s super spoilery (I hope!) But definitely play it safe.

Fingers crossed next run, as for the item there’s a

Yeah, I’ve never had

Definitely up there for the most notes I’ve taken playing a game for a while, some of them aren’t immediately obvious though their usefulness

Finally got

The back story as I said is probably the thing that kept me going, not 100% there but I needed to know if my own theories were correct.

Edit, also